16" Wide Restyler Ramps - Classic Model
$3,161.28
MSRP
Pricing shown as of 5/7/2026. Please note that prices are subject to change without notice.
Key Features:
- Full-length 14" lift for vinyl wrapping, detailing, display, or maintenance
- 16" ramp width; 82" to 128" adjustable wheelbase
- Five modular sections per ramp, no piece more than 40 lbs.
Technology & Features
Technology & Features
Specifications
Made in the USA
Sold As:
Pair
Length:
225"
Width:
16"
Height:
14"
Weight:
220 lbs.
Lift Height:
14"
Maximum Capacity:
6,000 lbs.
Maximum Tire Width:
14"
Approach Angle Degree:
10.4°
Material:
Expanded foam with traction coating
Color:
Black
More Information
The 16-inch wide Restyler Ramps Classic Model is exactly what you need in your shop for installing vinyl wrapping, paint protection and detailing as well as regular vehicle maintenance.
Developed by professionals for professionals, this portable wrap ramp system provides 14 inches of vehicle lift for better access to those tough-to-reach places. With an approach angle of 10.36 degrees, the 16-inch wide Restyler Ramp Classic Model accommodates wheelbases from 82 to 128 inches and tire widths up to 14 inches. The ramp system comes in five interlocking pieces, and once a car has been safely driven up and onto the blocks, the center pieces of the platforms can be pulled out and used as a step up, or removed to reach the underside of the vehicle. No piece weighs more than 40 pounds, making this system a great choice for on-location jobs in addition to regular shop use. The Restyler Ramps Classic Model a total vehicle weight capacity of 6,000 pounds.
The Restyler Ramps Classic Model is constructed of 100% solid, high-density foam with a rugged anti-slip coating that results in a lightweight ramp solution that is strong, yet durable. It won't slide on any surface, including garage and workshop floors.
- Full-length 14" lift for vinyl wrapping, detailing, display, or maintenance
- 16" ramp width; 82" to 128" adjustable wheelbase
- Five modular sections per ramp, no piece more than 40 lbs.
Usage Guidelines
Before using the ramps ensure other persons are clear of the vehicle and the ramps. Ensure that the ramps are free from damage or corrosion before use. Use only a single pair of wheel ramps at the front or rear, do not use two ramps on one side of the vehicle. Position the ramps in line with the wheels, with the steering wheel pointed straight and the incline against the tire tread. Carefully drive the vehicle onto the automotive ramps until it is in the correct position. Turn the engine off, apply the parking brake, get out of the vehicle and securely chock the remaining wheels on the ground. Before starting work, walk around the vehicle ensuring it is securely positioned. Always use jack stand if a person will be going under the vehicle. On completion of the work, check the parking brake is still firmly on and remove the chocks. It is important to drive very slowly when coming off the ramps to prevent the automotive bodywork from making contact with the car ramp. Exercise caution when using these car ramps with a trailer or three wheeled vehicles.
Calculator
Make sure you can sail right up your service ramps!
Use the calculator below to determine your vehicle's maximum angle of approach. Then shop for any Race Ramps with an angle equal to or less than your result.
To determine the best angle of approach for your vehicle, we have devised the “yardstick test” below. If you do not have a yardstick, carefully measure out 36" with a tape measure or other straight, rigid object.
You may need two sets of hands to get an accurate measurement.
YARDSTICK TEST
1
Place a 36" yardstick or tape measure at the base of your front wheel.
2
Raise up the yardstick or tape measure until it hits the underside of your car (the spoiler/splitter/air dam).
3
Measure vertically from the ground to the end of the yardstick or 36" point on the tape measure.
Record your height here.
Reviews
Reviews
Q&A
Q&A