Skip to Main Content Skip to Footer Content

80" Multi-Purpose Combo Ramps - 8.5 Degree Approach Angle

$564.00
ITEM #RR-80-10-2
Free Shipping
Made to Order, 3-4 Week Lead Time

Key Features:

  • Use as service ramp, trailer ramps or wheel cribs around the garage or shop
  • Provides 10" of lift for tires up to 12" wide
  • Set of two

See More…

Technology & Features
Tire Width
Tire Width
12" maximum width
Angle of Approach
Angle of Approach
8.5 degrees
Weight Capacity
Weight Capacity
1500 lbs. per ramp
Sold in Pairs
Sold in Pairs
2 ramps included
Lightweight
Lightweight
22 lbs. per ramp
100% SOLID
100% SOLID
Exclusive high-density foam
Anti Slip/Skid
Anti Slip/Skid
stays in place on any surface
80
30 Day Guarantee
Satisfaction or money back
80
Made in USA
and proud of it
RR-80-10-2 80 Multi-Purpose Combo Ramps - 85 Degree Approach Angle
Specifications
Made in the USA
Sold As:
Pair
Length:
80"
Width:
14"
Height:
12-1/4"
Weight:
22 lbs.
Lift Height:
10"
Maximum Capacity:
1,500 lbs.
Maximum Tire Width:
12"
Approach Angle Degree:
8.5°
Material:
Expanded foam with traction coating
Color:
Black
More Information

Our set of two-piece 80-inch Combo Ramps are the "triple header" of ramps! Use them as service ramps in the garage, trailer ramps when loading, or remove the ramp portion and use them as wheel cribs for display or service.

Engineered with a dual purpose, the ramp section of this two-piece design can be flipped over and used as a loading ramp for your low profile or lowered car with a convenient notch for your trailer door. Please note that this will not work for all trailers or vehicles, as it will depend on your trailer dimensions and car's front clearance angle. They have an 8.5-degree angle of approach and can hold up to 1,500 pounds each for a total vehicle weight capacity of 6,000 pounds yet each ramp only weighs 22 pounds. For more information about trailer ramps, please visit our trailer ramps page.

These ramps are manufactured using an exclusive, patented process. They are constructed of 100% solid, high-density foam with a rugged anti-slip coating that results in a lightweight ramp solution that is strong, yet durable. They won't slide on any surface, including ice and smooth auto shop floors.

  • Use as service ramp, trailer ramps or wheel cribs around the garage or shop
  • Provides 10" of lift for tires up to 12" wide
  • Set of two
Usage Guidelines
Please ensure that your ramp is damage-free before use. Never use two ramps on the same side of the vehicle. Use on a flat, level surface and ensure that the ramp makes full contact with the ground. Check that your steering wheel is straight and drive up at a slow, steady pace.

We stand by our Products! All Race Ramps purchases are backed by a 1 year warranty and are guaranteed to be free of defects at time of purchase.

WARNING: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Calculator
Make sure you can sail right up your service ramps!

Use the calculator below to determine your vehicle's maximum angle of approach. Then shop for any Race Ramps with an angle equal to or less than your result.

To determine the best angle of approach for your vehicle, we have devised the “yardstick test” below. If you do not have a yardstick, carefully measure out 36" with a tape measure or other straight, rigid object.

You may need two sets of hands to get an accurate measurement.

YARDSTICK TEST
yardstick test steps mobile
yardstick test step1
1

Place a 36" yardstick or tape measure at the base of your front wheel.

yardstick test step2
2

Raise up the yardstick or tape measure until it hits the underside of your car (the spoiler/splitter/air dam).

yardstick test step3
3

Measure vertically from the ground to the end of the yardstick or 36" point on the tape measure.

Record your height here.
Reviews
Q&A