Skip to Main Content Skip to Footer Content

Flatbed HD Tow Ramps

Starting at
Select Length
Select Description
Reset Selections
ITEM #flatbed-hd-tow-ramps
Free Shipping
Make a selection to see availability

Key Features:

  • 100% Solid lightweight high-density foam with traction coating
  • Easily extend rollback for faster, safer loading
  • Decrease angle of approach to as little as 5.2 degrees

See More…

Technology & Features
Tire Width
Tire Width
12" maximum width
Angle of Approach
Angle of Approach
5.2 degrees
Weight Capacity
Weight Capacity
2500 lbs. per ramp
Sold in Pairs
Sold in Pairs
2 ramps included
100% SOLID
100% SOLID
Exclusive high-density foam
Anti Slip/Skid
Anti Slip/Skid
stays in place on any surface
Flatbed HD Tow Ramps
30 Day Guarantee
Satisfaction or money back
Flatbed HD Tow Ramps
Made in USA
and proud of it
Made in the USA
Sold As:
Approach Angle Degree:
Maximum Capacity:
2,500 lbs.
Expanded foam with traction coating
More Information

Tow like a pro with our Heavy Duty Tow Ramps! Your customers love their Corvette, Porsche, or other low-to-the-ground car, and you need to show them that it's safe in your hands too.

The 7-inch Heavy Duty Tow Ramps give the vehicle 7 inches of lift over a 5.2-degree angle of approach. They are 74 inches long and 10 inches wide, and are designed for tires up to 8 inches wide. Available in a one-piece or two-piece version, the two-piece version is designed to be used as a singular unit with both pieces, or just as a compact version with one of the pieces. They can support up to 2,500 pounds per ramp, for a total vehicle weight capacity of 10,000 pounds. The 1-inch by 5-inch notch allows you to simply fold the rollback down into the notches and drive on up (or hook up the winch) with no worries about your safety or the safety of the car.

These ramps are manufactured with 100% solid, high-density foam with a rugged anti-slip coating. This patented process results in a product that is extremely lightweight, yet strong and durable. The ramps will not slide, scratch, or otherwise damage any floor type, and the reinforced bottom allows the ramps to be used on gravel or other rough surfaces that you may encounter along the side of the road.

  • 100% Solid lightweight high-density foam with traction coating
  • Easily extend rollback for faster, safer loading
  • Decrease angle of approach to as little as 5.2 degrees
  • Total vehicle weight capacity of 10,000 lbs.
  • Set of two
Usage Guidelines
Please ensure that your ramp is damage-free before use. Never use two ramps on the same side of the vehicle. Use on a flat, level surface and ensure that the ramp makes full contact with the ground. Check that your steering wheel is straight and drive up at a slow, steady pace.

We stand by our Products! All Race Ramps purchases are backed by a 1 year warranty and are guaranteed to be free of defects at time of purchase.

WARNING: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to
Make sure you can sail right up your service ramps!

Use the calculator below to determine your vehicle's maximum angle of approach. Then shop for any Race Ramps with an angle equal to or less than your result.

To determine the best angle of approach for your vehicle, we have devised the “yardstick test” below. If you do not have a yardstick, carefully measure out 36" with a tape measure or other straight, rigid object.

You may need two sets of hands to get an accurate measurement.

yardstick test steps mobile
yardstick test step1

Place a 36" yardstick or tape measure at the base of your front wheel.

yardstick test step2

Raise up the yardstick or tape measure until it hits the underside of your car (the spoiler/splitter/air dam).

yardstick test step3

Measure vertically from the ground to the end of the yardstick or 36" point on the tape measure.

Record your height here.